Printronix P6000L Скачать руководство пользователя страница 166

Страница: 166 / 234

Interfaces

7-8

Alternate Terminating Resistors

For parallel interface configurations, the printer is equipped with 1K ohm pullup terminating

resistors located at U1 and U3 of the I/O cable assembly PCBA. Generally, the 1K ohm termiĆ

nating resistors are suitable for most applications. If, however, the standard terminating resisĆ

tor pack is not compatible with the particular interface driver requirements of the host, 220

ohm pullup and 330 ohm pulldown alternate terminating resistors are provided.

Printronix

recĆ

ommends using the 330 ohm pulldown resistors in conjunction with the 220 ohm pullup resisĆ

tors.

Floor Cabinet Model

To install the alternate terminating resistors in the floor cabinet model, perform the following

instructions.

Turn off the printer and disconnect the ac power cord.

Remove the six screws securing the I/O panel at the lower rear corner of the printer as

shown in Figure 7-1.

Slide the entire I/O assembly straight out of the printer until the I/O PCBA is accessible.

Remove the 1K ohm resistor packs from the sockets at locations U1 and U3 on the I/O

PCBA as shown in Figure 7-1.

Plug the 220 ohm resistor pack into the socket at locations U1.

Plug the 330 ohm resistor pack into the socket at U2.

Slide the I/O assembly back into the printer.

Replace the I/O panel and secure it with the six screws.

Reconnect the ac power cord and turn the printer on.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды