Printronix P6000L Скачать руководство пользователя страница 159

Страница: 159 / 234

7-1

Interfaces

CHAPTER 7

INTERFACES

Introduction

P6000L/P6200L Series printers are equipped with resident parallel and serial interfaces. Each

printer is configured at the factory for either Dataproducts parallel, Centronics parallel, or

RS-232 serial interface. If required, an interface conversion kit is available from

Printronix

Contact your authorized representative for details.

NOTE: If a change is made from a Dataproducts parallel to a Centronics parallel interĆ

face or vice versa, the I/O cable and connector assembly must be changed as described in

the Interface Conversion Kit instructions. Parallel interface configuration parameters

can be modified as required by the application. If a change is made from either parallel

interface to the RS-232 serial interface or vice versa, the jumper platform at location 6A

on the C3 logic board must be reversed (removed, turned around, and reinstalled) in adĆ

dition to changing the I/O cable and connector assembly and the interface configuration

parameters. Refer to the Interface Conversion Kit instructions and the Interface Jumper

Platform section in this chapter for details.

This chapter describes:

Dataproducts Parallel Interface

Centronics Parallel Interface

RS-232 Serial Interface

Alternate Terminating Resistors

Floor Cabinet Model

Pedestal Model

Interface Jumper Platform

Dataproducts Parallel Interface

This interface allows the printer to operate with controllers designed for Dataproducts printĆ

ers using a 50 pin AMP Ampilite HDH-20 type connector. The interface is capable of transĆ

ferring up to 300,000 characters per second. The maximum data line cable length from the

controller or host computer to the printer is 40 feet.An optional Dataproducts long lines

adapter is available, permitting cable length up to 2000 feet.

Dataproducts Interface Signals

Dataproducts compatible interface signals between the computer and the printer are defined

as follows. Table 7-1 lists the Dataproducts interface connector pin assignments.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды