Printronix P6000L Скачать руководство пользователя страница 164

Страница: 164 / 234

Interfaces

7-6

Transmit Clock (TC)

- An optional timing signal for transmitted data that may be provided by

a Data Set with synchronous interface.

Receive Clock (RC)

- An optional timing signal for Received Data that may be provided by a

Data Set with synchronous interface.

External Clock (EC)

- An asynchronous timing clock stream pulsed at 16 times the data bit

input rate from an external TTL source when external baud rate has been selected.

Table 7-3. Serial Interface Pin Assignments

INPUT SIGNALS

OUTPUT SIGNALS

SIGNAL

Received Data

Clear To Send

Data Set Ready

Carrier Detect

Transmit Clock

Receive Clock

External Clock

Transmitted Data

Request To Send

Data Terminal Ready

Chassis Ground

Reverse Channel Send

Signal Ground

11,14

Serial Interface Protocols

The following serial interface protocol characters are available. The protocol is configuration

selectable from the control panel to meet host interface requirements.

XON/XOFF

- The printer transmits an XON (11 Hex) character when entering the online

state or when the buffer is almost empty. The printer transmits an XOFF (13 Hex) character

when entering the offline state or when the buffer is almost full.

ETX/ACK

- With ETX/ACK protocol selected, the printer interface operates in a block strucĆ

tured mode. The host sends a block of data (commonly 128 characters) in response to an ACK

(06 Hex) character sent from the printer. The host marks the end of the block of data with an

ETX (03 Hex) character. When the printer recognizes the ETX character, the printer releases

the data block to be printed and checks the space available in the buffer. If space is available for

the next block of data, the printer sends ACK to the host. If space is not available, the printer

withholds ACK until sufficient space is available.

ACK/NAK

- With ACK/NAK protocol selected, the printer responds as described for ETX/

ACK protocol except the printer monitors the received data for parity error. If a parity error is

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды