Printronix P6000L Скачать руководство пользователя страница 41

Страница: 41 / 234

2-21

Operation

Figure 2-16. Ribbon Replacement

Setting Forms Length

P6000L/P6200L Series printers may use continuous, tractor-fed paper with the forms length

set in inches (between 1.0 and 24.0) or lines (between 1 and 192 at 6 or 8 lines per inch). Setting

the forms length in lines at 6 or 8 lpi does not change the line spacing. The printer has been

preset for standard 11-inch length paper. Therefore, when using alternate length paper, the

top-of-form setting and the forms length setting must be changed to match the alternate

length. To set the forms length:

Place the printer offline.

Simultaneously press RUN/STOP TEST and CONFIG MENU to unlock the printer conĆ

figuration.

Press FORMS LENGTH; the display will show the current FORMS LENGTH SET IN

INCHES.

Continuously pressing FORMS LENGTH will step the display through the following opĆ

tions: FORMS LENGTH SET IN 6 LPI LINES, FORMS LENGTH SET IN 8 LPI

LINES, and FORMS LENGTH SET IN INCHES. Choose the appropriate setting, perĆ

form the corresponding instructions, and then save the selected forms length.

To set the forms length in inches:

Press FORMS LENGTH until FORMS LENGTH SET IN INCHES is displayed.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды