Printronix P6000L Скачать руководство пользователя страница 209

Страница: 209 / 234

10-19

Installation

Preliminary Test

After installation is complete, the printer is ready for preliminary testing. The following steps

define the test procedure. See the Operation chapter for a description of the control panel and

message display.

Set the ac power switch to ON and verify the POWER indicator is lit.

Load full width computer paper and ribbon as described in the Operation chapter.

Close the front cover.

Press the ON LINE switch until the message display reads OFFLINE READY

Press the TOP OF FORM switch. The paper will advance to the next top-of-form

(TOF). Refer to the Operation chapter for TOF procedure.

Press the CONFIG MENU switch until DIAGNOSTICS appears. Press CONFIG

VALUE once; CONFIGURATION PRINTOUT will appear.

NOTE: Ignore the two CONFIGURATION LOCKED messages briefly displayed. The

printer configuration does not have to be unlocked to run self tests.

Press the CONFIG MENU switch until the PRINTER TEST FULL WIDTH menu apĆ

pears.

Press the CONFIG VALUE switch. The SHIFT RECYCLE message should appear.

Press the RUN/STOP TEST switch. The RUNNING TEST SHIFT RECYCLE message

appears. Shifted lines of the alphabet will print across the full width of the paper (132

characters).

10. To stop the test press the RUN/STOP TEST switch once. Press CLEAR FAULT repeatĆ

edly to return to off line.

Examine the print quality. Make sure the characters are fully formed and of uniform density. If

the test does not run or characters appear malformed, make sure that the forms thickness lever

is correctly adjusted for the paper thickness. Call your authorized Service Representative for

further assistance.

11. To test the printer to host computer interface, press the ON LINE switch and send several

lines of data from the host computer to the printer.

If errors such as wrong characters printed or intermittent paper motion are observed, it may be

necessary to install the alternate terminating resistors as described in the Interface chapter.

With a Centronics interface, if missing or doubled characters are observed, it may be necessary

to change the strobe polarity jumper from E49-E50 to E50-E51. With a RS-232 interface,

verify correct operation with a terminal, and re-check the printer configuration. Refer to the

Hardware Jumper Configuration section in the Configuration chapter for more information.

Call your authorized Service Representative for further assistance.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды