Printronix P6000L Скачать руководство пользователя страница 27

Страница: 27 / 234

2-7

Operation

Diagnostics

After the required menu is displayed, individual parameters are displayed using the CONFIG

VALUE switch as shown on the Control Panel Switch Function Diagram in the Configuration

chapter.

CONFIGURATION VALUE -

Press Configuration Value (CONFIG VALUE) to display indiĆ

vidual configuration parameters and the current value from within the main menus.

NOTE: Alternately and/or repeatedly pressing CONFIG MENU and CONFIG VALUE

allows the display of the configuration parameters as shown on the Control Panel Switch

Function Diagram in the Configuration chapter. The CONFIG MENU and CONFIG

VALUE switches when pressed simultaneously step backward through the configuration

menu, forms length, and print mode selections.

RUN/STOP TEST -

The RUN/STOP TEST switch performs the following functions:

Press RUN/STOP TEST simultaneously with CONFIG MENU to alternately unĆ

lock and lock the printer configuration..

Press RUN/STOP TEST to select a configuration parameter, forms length, or print

mode. An asterisk (*) will appear to the right of the value to indicate that it has been

selected.

Press RUN/STOP TEST simultaneously with CLEAR FAULT to reset the printer.

If a self-test is selected and shown on the display, press RUN/STOP TEST to start

the test and press it again to stop the test.

If the CONFIGURATION PRINTOUT message is selected and shown on the disĆ

play, press RUN/STOP TEST to print a list of the current configuration. Press RUN/

STOP TEST again to return to OFFLINE READY.

CLEAR FAULT -

Press this switch to reset the printer after a fault condition has been corĆ

rected. Fault conditions are indicated on the display. After pressing CLEAR FAULT the disĆ

play will indicate the printer is offline if the fault was corrected.

In addition, the CLEAR FAULT switch performs two special functions:

Press CLEAR FAULT simultaneously with RUN/STOP TEST to reset the printer.

Press CLEAR FAULT when one of the parameter values is displayed to move up one

menu parameter selection or to offline. Refer to the Control Panel Switch Function

Diagram in the Configuration chapter.

Paper Adjustment Controls

The printer paper loading controls for the floor cabinet model are shown in Figure 2-4. The

printer paper loading controls for the pedestal model are shown in Figure 2-5. The controls

are the Forms Thickness Adjustment Lever (A), the Vertical Position Knob (B), the Horizontal

Adjustment Knob (C), and the paper tractors (D). The PAPER ADVANCE switch on the conĆ

trol panel is also used during the paper loading procedure.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды