Printronix P6000L Скачать руководство пользователя страница 143

Страница: 143 / 234

6-43

Programming

Plot, Even Dot (P-Series High Density Graphics)

P-SERIES

SERIAL MATRIX

ASCII Code

EOT

Hex Code

Purpose

Prints dots at the even numbered dot columns.

Expression

CHR$(4);

Comment

The even dot plot code is used for programming high density graphics and

must be used in conjunction with the Odd Dot Plot code (05 Hex). This code

should occur before any printable data in the data stream for maximum

throughput. In even dot plot, line feed codes do not cause paper motion. ReĆ

fer to the Graphics chapter for more information.

Example

The following sample program illustrates two high density plot boxes using

odd and even dot plot for high density graphics. Compare the example below

to the plot, odd plot control code example.

Содержание P6000L











































































































































































































































Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды

Printronix P6000L, Руководство пользователя

Результаты поиска

Содержание P6000L

Отзывы:

Похожие инструкции для P6000L

Бренды по названию

Популярные бренды