Pearson CE35-T Case Скачать руководство пользователя

Страница: 90 / 144

Log In

The Log In screen determines the level
of accessibility to the operations screens
in the HMI.

The Operator level has the lowest
access level. The operator can
change the case size.

The Maintenance level has the next
level of accessability with access to
the timer and float value screens.

The OEM level of access is the
highest for the Pearson Service
Technicians.

Note:

You can log in using the Log In screen or on the individual HMI screens that
require a log in there will be a log in button. The instructions are the same for
both.

Press Log In.

A screen will appear with User and Password.

Press User and select the level of access you have been assigned.

Press Password and enter your password.

Log Out Procedure:

Press Log Out

or:

If the screens are not accessed within 12 minutes, the HMI will
automatically log out.

CE35-T Case Erector

Operations Manual

3/2/2010

M-CE35T-2c Horiz Mag

a
M-

a
m

)I
M

Fig. 70: Log In Screen

Содержание CE35-T Case

















































































































































Результаты поиска

Содержание CE35-T Case

Отзывы:

Похожие инструкции для CE35-T Case

Бренды по названию

Популярные бренды

Pearson CE35-T Case, Руководство по эксплуатации

Результаты поиска

Содержание CE35-T Case

Отзывы:

Похожие инструкции для CE35-T Case

Бренды по названию

Популярные бренды