Pearson CE35-T Case страница 135 Скачать руководство пользователя

Страница: 135 / 144

How to Replace the Primary Belt …

Remove the guard.

Jog the machine until the pick-off arm
reaches the maximum rearward
extension at the magazine.

Remove the connecting pin that attaches
the arms to the pick-off carriage.

Remove the worn, damaged or defective
belt.

Place the replacement belt on the
sprockets.

Replace the pin that connect the arms to
the pick-off carriage.

Temporarily tension the belt.

Jog the machine flights to the 0 (zero) position.

When the machine flights are at the 0 (zero) position, the pick-off arm
should be the top dead center or 12:00 position.

10. Tension the belt to 20 lbs. force = .75 inches inflection.

Measure the belt tension on the longest span of the belt, not on the idler
side.

11. Check the alignment of the primary arms.

Operations Manual

CE35-T Case Erector

M-CE35T-2c Horiz Mag

3/2/2010

w
T

119

Fig. 97: Manual Control Screen

Содержание CE35-T Case

















































































































































Результаты поиска

Содержание CE35-T Case

Отзывы:

Похожие инструкции для CE35-T Case

Бренды по названию

Популярные бренды

Pearson CE35-T Case, Руководство по эксплуатации

Результаты поиска

Содержание CE35-T Case

Отзывы:

Похожие инструкции для CE35-T Case

Бренды по названию

Популярные бренды