Pearson CE35-T Case Скачать руководство пользователя страница 129

Страница: 129 / 144

13. If the sensors need to be moved, loosen the at tach ment bolts.

14. From the front edge of the sensor mount to the center of the bolt on the

sensor bracket (approximately 7 to 7 ½”) position the Load Magazine Full
PE2 sensor.

Aim towards the Pick-Off Magazine Full PE3 sensor so the beams cross
at 4" (102 mm) to 5" (127 mm) from the corners of the blanks.

15. From the front edge of the sensor mount to the center of the bolt on the

sensor bracket (approximately 3 to 3 ½”) position the Pick-Off Magazine
Full PE3 sensor.

Aim towards the Load Magazine Full PE2 sensor so the beams cross at
4" (102 mm) to 5" (127 mm) from the corners of the blanks.

16. Make sure bolts are suf fi ciently tight so that ma chine vi bra tion does not

cause the sensors to shift.

Operations Manual

CE35-T Case Erector

M-CE35T-2c Horiz Mag

3/2/2010

w
T

113

Fig. 88: Positioning the sensors

Attachment

Bolt

Load Magazine

Full PE2

sensor

Pick-Off

Magazine Full

PE3 sensor

7” to 7

”

Front Edge of

Sensor Mount

Содержание CE35-T Case

















































































































































Результаты поиска

Содержание CE35-T Case

Отзывы:

Бренды по названию

Популярные бренды

Pearson CE35-T Case, Руководство по эксплуатации

Результаты поиска

Содержание CE35-T Case

Отзывы:

Бренды по названию

Популярные бренды