Pearson CE35-T Case Скачать руководство пользователя

Страница: 134 / 144

In the enter setup values screen, ensure
the case size selected in step 3 is
displayed on the screen as the current
case size.

Take a case blank and begin adjusting
the machine, using the Changeover
chapter in this manual as a reference.

Using the directional keys, select the
setup value that is being adjusted.

Pressing the Enter Preset button accesses
the “preset value” screen for inputting
the new value. When the screen is opened the preset value populates to “0.”

Note:

Use Ec function button in the value screen to escape the screen without saving
changes to the preset value.

10. The HMI directional keys are used for inputting the new numbers.

Up/Down directional keys will increase or decrease the number. Number
sequence is 0-9 then decimal point.

Left/right directional keys will move the cursor left or right.

11. Use the Enter key to set the new value.

12. When the enter setup values screen appears again the new value should be

displayed for the adjustment just entered.

13. Repeat the process for all the case adjustment points.

Note:

For information on adding an additional case size to the HMI please contact our
Service Department Tech Support at 800-732-7766.

CE35-T Case Erector

Operations Manual

3/2/2010

M-CE35T-2c Horiz Mag

118

T
w

Fig. 96: Enter Setup Values

Screen

Содержание CE35-T Case

















































































































































Результаты поиска

Содержание CE35-T Case

Отзывы:

Похожие инструкции для CE35-T Case

Бренды по названию

Популярные бренды

Pearson CE35-T Case, Руководство по эксплуатации

Результаты поиска

Содержание CE35-T Case

Отзывы:

Похожие инструкции для CE35-T Case

Бренды по названию

Популярные бренды