Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 18

Страница: 18 / 147

Using OmniStream

™

with Velocity

™

Device Manager

Basic Configuration Tutorial

4. Click the

HDCP

Version

drop-down list to restrict HDCP to a particular version. By default, this is set to

2.2

and this setting should be used for most applications.

5. The

Video

section provides information about the input signal: color depth, subsampling, color space,

resolution, frame rate, and HDR (High Dynamic Range). If the HDR indicator is green, this will indicate that HDR

content is being transmitted from the source device. Refer to the

INPUT page (page 94)

for more information.

The

Audio

section displays audio information (if present) from the source device: bit depth, the number of audio

channels, the audio format, and the frequency. Refer to the

INPUT page (page 94)

for more information.

7. Click

SAVE

in the bottom-right corner of the

HDMI Input 1

window group to commit changes.

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды