Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 118

Страница: 118 / 147

Using OmniStream

™

with Velocity

™

Device Manager

118

Subframe window groups

The Velocity/OmniStream Interface

The name of these window groups will change, based on the multiview layout that is selected. However, the

information contained within the window group will be the same.

Name

The name of the subframe and the resolution of the subframe. This field cannot be modified.

Input

Click this drop-down list to select the desired IP input.

Enter the x-position of the anchor point in this field.

Enter the y-position of the anchor point in this field.

Anchor

Click this drop-down list to select the anchor point for the subframe. Anchor points are:

top left

top right

bottom left

bottom right

, and

center

Z-order

Enter the z-order value in this field. Subframes with a higher z-order value will be moved to the front (on top of)

subframes with lower z-order values.

Input Status

Displays the status and resolution of the input, if it is active. If it is not active, then

No Video

will be displayed.

Output Status

Displays the status and resolution of the output, if it is active. If it is not active, then

No Video

will be displayed.

DELETE

Deletes the subframe from the multiview window group.

SAVE

Click this button commit changes to the subframe window group.

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды