Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 89

Страница: 89 / 147

Using OmniStream

™

with Velocity

™

Device Manager

Advanced Operation

1. Go to the encoder/decoder, click

NETWORK

in the menu bar, then click the

802.1x Mode

drop-down list and

select the desired authentication method. In the example below,

PEAP/MSCHAPv2

is selected.

Once a method is selected, the required fields for that method will be displayed. Enter the required information

in each field. For the

PEAP/MSCHAPv2

option, the fields are described as follows:

Field

Description

Identity

Enter the identity of the authentication server in this field. PEAP uses this field to

identify the correct authentication server which will process the credentials. For

example, if

[email protected]

is entered, then this identifies AUTHSERV as the

RADIUS (authentication) server.

Password

Enter the password in this field.

CA certificate

Select the certification authority (CA) certificate.

NOTE:

If using dual-channel encoders, both

Network 1 (eth1)

and

Network 2 (eth2)

will need

to be set up, depending upon the system requirements.

Authentication Method

Identity

Password

CA Certificate CA Certificate Client Private

Certificate

PEAP/MSCHAPv2
EAP-TLS

Refer to the table below for a list of available authentication methods. An orange dot indicates that this field will

be displayed as part of the method.

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды