Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 82

Страница: 82 / 147

Using OmniStream

™

with Velocity

™

Device Manager

Device Operation

Fast Switching FAQs

Question

Does fast switching work between streams of different resolutions?

Answer

Yes. Fast switching can be used between streams with different resolutions and frame rates.

Question

Does fast switching work between HDR and SDR streams?

Answer

Yes, fast switching can be used between HDR and SDR streams; however, it’s important to note that

some color artifacts may appear during the switch.

Question

Does fast switching work between single streams and multiviews or between multiviews?

Answer

No. Due to the way multiviews work, fast switching is not supported. However, it is not necessary to

change the fast switching setting – the decoder will switch as fast as possible between multiviews

and return to fast switching when single streams are used.

Question

Does fast switching work on video walls?

Answer

No. Fast switching is not supported when using video walls.

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды