Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 62

Страница: 62 / 147

Using OmniStream

™

with Velocity

™

Device Manager

Preset Orientation

There may be some situations in which content that is spread across multiple displays must be rotated.

Two examples are shown below.

In the following example, a single source is spread across three vertical displays. The source content (shown on the

left) is rotated -90 degrees. In order for the content to be displayed correctly, the source must be rotated.

Figure 1.1 - Source content

Figure 1.2 - Source content properly rotated to span three vertically rotated

displays.

Example 1: Content requiring rotation.

1. Click the icon in the upper-right

corner of the screen. The source

dialog will be displayed.

2. Locate the

Disable Rotation

toggle

switch at the bottom of the dialog.

3. Verify that the toggle switch is set

to the far-left position. The toggle

switch will be gray when rotation is

enabled

4. Click

CLOSE

to commit changes and

dismiss the dialog box.

Device Operation

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды