Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 3

Страница: 3 / 147

Using OmniStream

™

with Velocity

™

Device Manager

Sales, Marketing, and Customer Support

Operating Notes

Warranty

To view the product warranty, use the following link or QR code:

https://atlona.com/warranty/.

Main Office

Atlona Incorporated

70 Daggett Drive

San Jose, CA 95134

United States

Office: +1.408.962.0515

Sales and Customer Service Hours

Monday - Friday: 6:00 a.m. - 4:30 p.m. (PST)

https://atlona.com/

International Headquarters

Atlona International AG

Tödistrasse 18

8002 Zürich

Switzerland

Office: +41.43.508.4321

Sales and Customer Service Hours

Monday - Friday: 09:00 - 17:00 (UTC +1)

IMPORTANT:

Visit http://www.atlona.com/ for the latest firmware updates and User Manuals

for both OmniStream

™

and Velocity

™

Device Manager.

IMPORTANT: The

AT-OMNI-122 does

not

support VCx mode. Installations that use the

AT-OMNI-122 should make sure that all devices in the system are on the same VC-2 mode.

Refer to

DEVICE INFO page (page 113)

for more information.

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды