Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 101

Страница: 101 / 147

Using OmniStream

™

with Velocity

™

Device Manager

101

Scrambling

Click this toggle switch to enable or disable scrambling on the encoder. Atlona recommends enabling scrambling for

security purposes. When enabled, the toggle switch will be green.

Key

This field is only displayed if the

Scrambling

toggle switch is enabled (green). Enter the scrambling key in this field.

The scrambling key must be ASCII and must contain a minimum of eight characters. Special characters and spaces

are not permitted.

The Velocity/OmniStream Interface

Video

Audio

Encoder

Click this drop-down list to select the encoder input.

Enable Video

Click this toggle switch to enable or disable the video signal. When enabled (green), video will pass from the encoder

to the decoder.

Destination Multicast/Unicast Address

Enter the IP address that will be used to stream the content.

Destination UDP Port

Enter the destination UDP port in this field.

TTL

Set the

TTL (Time-To-Live) duration, from 1 to 255 seconds, in this field. The default value is 255 seconds.

DSCP

Click this drop-down list to select the DSCP value. Refer to

Differentiated Services Code Point (page 146)

for more

information on this topic.

FEC Enable

Click this toggle switch to enable (green) or disable Forward Error Correction (FEC). This feature can be used when

transporting streams over a network that is suspected to be unreliable, due to noise or other factors. By default, this

feature is enabled. Refer to

FEC Details (page 144)

for more information.

FEC Rows

Specify the number of FEC rows in this field. Refer to

FEC Details (page 144)

for more information.

FEC Columns

Specify the number of FEC columns in this field. Refer to

FEC Details (page 144)

for more information.

LINK TEST

Click this button to perform a link integrity test. This feature validates the quality of the link between the encoder

and decoder. Link tests are initiated at an encoder, and any decoders that are configured to join that encoder’s video

multicast address will return packet loss statistics to the encoder, which displays the combined results under the

Notifications

tab. Refer to

Performing a Link Test (page 141)

for more information.

Source

Click this drop-down list to select the desired input.

Enable AES67

Click this toggle switch to enable AES67. When this feature is enabled, the toggle switch will be green.

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды