Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 13

Страница: 13 / 147

Using OmniStream

™

with Velocity

™

Device Manager

Getting Started

7. Click the desired OmniStream device from the

Unassigned

list.

8. The control interface for the device will be displayed and the device can be configured as desired.

The illustration below shows the

DEVICE INFO

screen for an AT-OMNI-112 encoder.

If a DHCP server is not found within 60 seconds, the encoder will be placed in Auto IP (APIPA) mode and

assigned an IP address within the range of

169.254.xxx.xxx/16

. If this occurs, configure the network

interface of the computer that is running Velocity, located on the same subnet (

169.254.xxx.xxx

, subnet mask

255.255.0.0

). Refer to

Configuring a Static IP Address (page 87)

for more information on configuring an

encoder in Auto IP mode.

If no OmniStream encoders are found, then verify the following:

• The computer that is running Velocity must be on the same network as the OmniStream device.

• Remove any network restrictions that may be in place. In order for mDNS to function properly, there

must not be any restrictions applied to the network.

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды