Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 142

Страница: 142 / 147

Using OmniStream

™

with Velocity

™

Device Manager

142

5. The

LINK TEST

button will be hidden and an animated icon will appear, indicating that the link test is in progress.

After the link test has completed, the

LINK TEST

button will be displayed.

7. Click

NOTIFICATIONS

in the menu bar to review the test results.

Appendix

If the test passed, information similar to the following will be displayed: “100% of packets received by ...”

indicates no packets were dropped / zero loss.

If the test fails, it could be that less than 100% of packets are received, indicating connectivity, but with some

amount of packet loss. If it shows “No one replied!” or if the target decoder is not shown in results, it could

indicate that there is a connectivity issue or that the decoder is not subscribed to the correct video multicast

address.

Click the

CLEAR

button to remove the test results from the

NOTIFICATIONS

page.

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды