Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 49

Страница: 49 / 147

Using OmniStream

™

with Velocity

™

Device Manager

Device Operation

2. Click the

INPUT

menu.

3. Under the

HDMI Input 1

window group, select

Default HDR MCH

from the

EDID

drop-down list.

4. Click the

Supported Version

drop-down list and select

2.2

. Click the

SAVE

button, under the

HDMI Input 1

window group, to commit changes.

5. Under the

Encoder 1

window group, click the

Input

drop-down list and select

HDMI Input 1

Set the

Max Bit Rate

field to

450

7. Click the

Scaler

drop-down list and select

1920x1080

Click the

Thumbnail

Enable

toggle switch to enable thumbnails of the source. This will verify that the input

source is configured correctly and will provide a visual reference for the encoder stream. Thumbnails are

updated every 2 seconds.

1. Click

DEVICE INFO

in the menu bar, then click the

System Mode

drop-down list and select

VCx

. Click the

SAVE

button, in the lower-right corner of the screen, to commit changes.

Dual-Streaming Encoder Configuration

IMPORTANT: VCx

must be enabled in order to use the Multiview feature.

NOTE:

Thumnails can also be accessed at:

http://<encoder-ip-address>/thumbnail/

thumbnail1.jpg

. For dual-channel encoders, the secondary thumbail can be accessed at:

http://<encoder-ip-address>/thumbnail/thumbnail2.jpg

9. Click the

SAVE

button, under the

Encoder 1

window group, to commit changes.

10. Under the

Encoder 2

window group, select

HDMI Input 1

from the

Input

drop-down list.

11. Set the

Max bit rate

field to

150

12. Click the

Scaler

drop-down list and select

1280x720

13. Click the

SAVE

button, under the

Encoder 2

window group, to commit changes.

14. Click

SESSION

in the menu bar and configure each video stream using the information in the table bellow.

Audio streams will not be configured for this tutorial.

Encoder #1

Stream

Interface

Encoder

Destination

Multicast/Unicast Address

Destination UDP Port

Stream 1

eth1

Encoder 1

226.0.0.1

1000

Stream 2

eth1

Encoder 2

226.0.0.2

1000

15. Click the

SAVE

button, under both

Stream 1

and

Stream 2

window groups, to commit changes.

This encoder is used with the HD camera and will be configured to dual-stream 1080p and 720p.

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды