Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 63

Страница: 63 / 147

Using OmniStream

™

with Velocity

™

Device Manager

In this example, three sources are spread across three vertical displays. The content (shown on the left) was created

to be displayed horizontally. In this case, rotating the source is not required.

Figure 1.1 - Source content

Source 1

Source 2

Source 3

Figure 1.2 - Source content properly rotated to span three vertically rotated

displays.

Example 2: Content that does not require rotation.

1. Click the icon in the upper-right corner of the source window.

The source dialog will be displayed.

2. Locate the

Disable Rotation

toggle switch at the bottom of the

dialog.

3. Verify that the toggle switch is set to the far-left position. The toggle

switch will be green when rotation is

disabled

4. Click

CLOSE

to commit changes and dismiss the dialog box.

5. Repeat steps 1 through 4 for each source.

Device Operation

Source 1

Source 2

Source 3

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды