Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 22

Страница: 22 / 147

Using OmniStream

™

with Velocity

™

Device Manager

Subscribing to an Encoder

The next step is to configure the decoder so that it is able to receive video, audio, and/or data (control) streams from

the encoder. This process is referred to as “subscribing to the encoder”.

1. Go to the decoder, click

IP INPUT

in the menu bar, and locate the IP Input 1 window group. Verify that the

Enable

toggle switch is enabled. When enabled, the toggle switch will be green. Perform the same procedure

for the

IP Input 2

window group.

2. Under the

IP Input 1

window group, enter

226.0.0.1

in the

Multicast Address

field. Under the

IP Input 2

window group, enter

226.0.0.2

in this field. These multicast IP address are the same addresses that were

specified under the

Video

Destination Multicast/Unicast Address

field for the encoders.

3. In the

Port

field, enter

1000

under both

IP Input 1

and

IP Input 2

window groups. These are the same port

settings that were entered under the

Video

Destination UDP Port

field of the encoder.

4. Click the

SAVE

button, under the

IP Input 1

and

IP Input 2

window groups, to commit changes.

Basic Configuration Tutorial

Video Configuration

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды