Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 70

Страница: 70 / 147

Using OmniStream

™

with Velocity

™

Device Manager

Device Operation

The first Drop Zone will can dynamically apply sources to the preset, which is a 2x2 video wall, to the top-left,

bottom-left, and both or only one display(s) on the right-hand side. Some possible combinations are shown

below. Drop Zone containers have been labeled alphabetically, for reference.

Note that although the top-right and bottom-right displays are physically separate, dragging and dropping a

source from the left-hand side of the screen to Drop Zone container “C”, will “map” the source to both displays.

To change to a different source, drag and drop a source from the left-hand side of the screen to the source to be

replaced.

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды

Panduit ATLONA OmniStream 101, Руководство пользователя

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Похожие инструкции для ATLONA OmniStream 101

Бренды по названию

Популярные бренды