Panduit ATLONA OmniStream 101 Скачать руководство пользователя страница 94

Страница: 94 / 147

Using OmniStream

™

with Velocity

™

Device Manager

The Velocity/OmniStream Interface

The

INPUT

page provides signal information for each channel (input). The following fields apply to both the

HDMI

Input 1

and

HDMI Input 2

window groups. Single-channel encoders only have a single

HDMI Input

window group.

Input

The selected input.

Max Bit Rate

Click this field to enter the maximum bit rate. The default setting is

750

Mbps. 4K60 4:4:4 streams should be at

least 700 Mb/s, 4K30 4:4:4 streams should be at least 350 Mb/s, and 1080p streams should be at least 150 Mb/s.

Setting this field below these recommended values will result in lower-quality video.

Subsampling

Click this drop-down list to select the chroma subsampling value. Available values are:

4:4:4

4:4:2

, and

4:2:0

Encoder window group

INPUT page

Содержание ATLONA OmniStream 101




















































































































































Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы:

Panduit ATLONA OmniStream 101, Руководство пользователя, Страница: 94 / 147

Результаты поиска

Содержание ATLONA OmniStream 101

Отзывы: