Omron ZW-7000 Series Скачать руководство пользователя страница 252

Страница: 252 / 336

Setting the Output Conditions

250

ZW-8000/7000/5000

User's Manual

Performing Thickness Scaling

Performing Thickness Scaling p.151

Operating procedure

Steps

Key operation

Display

Description

1 to 5

For moving to “SCALE”, see steps 1 to 5 in p.246.

Select “THICK” as the scaling type.
The current setting value is displayed on the sub-display.

Press

key to enter editing mode and the sub-display blinks.

Select “THICK” and press the

key.

The current measured value is displayed on the main display and the
current setting value is displayed on the sub-display.

Press

key to enter the editing mode, and the sub-display

blinks.

To edit numerical values, use the

keys.

Enter the setting value and then press the

key.

“OK/CAN” is displayed on the sub-display.
When continuing to set the next point measurement value, press the

key. When ending all point settings, press the

key.

Press and hold the

key for two seconds or more to enter the

RUN mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222).

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Omron ZW-7000 Series, Руководство пользователя

Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды