Omron ZW-7000 Series Скачать руководство пользователя страница 270

Страница: 270 / 336

Setting the System

268

ZW-8000/7000/5000

User's Manual

7-11 Setting the System

Display/set the system environment.

Checking Information

Display the set measuring cycle and information of the Sensor Controller and Sensor Head.

Checking the Information of the Sensor p.192

As an example, here is an explanation of the procedure for displaying the serial No. of the Sensor Head.

Operating procedure

Steps

Key operation

Display

Description

Press and hold the

key for two seconds or more to enter the

FUNC mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222)

Press the

keys to select “SYSTEM” and press the

key.

Select the information to display.

C.INFO: CONTROLLER INFORMATION
H.INFO: SENSOR HEAD INFORMATION

In this example, press the

keys, select “H.INFO” and

press the

key.

When the Controller information and Sensor Head information have
been changed, select the additional information to display:

VER: Controller version information
MAC.ADR: Controller MAC address
MODEL: Sensor Head model information
SER.NO: Sensor Head serial No.

In this example, press the

keys, select “SER.NO” and

press the

key.

“SER.1” is displayed on the main display and the higher-order digit of
the serial No. is displayed on the sub-display.

When the

key is pressed, “SER.2” is displayed on the

main display and the lower-order digit of the serial No. is displayed
on the sub-display.

Press and hold the

key for two seconds or more to enter the

RUN mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222).

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Omron ZW-7000 Series, Руководство пользователя

Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды