manualshive.com logo in svg

Omron ZW-7000 Series, Руководство пользователя

Поделиться
Скачать
Omron ZW-7000 Series Скачать руководство пользователя страница 57

System Configuration

ZW-8000/7000/5000 
User's Manual

 2

In

sta
llatio

n

 a

nd 

Con

nection

s

55

Connection Compatibility

• EtherCAT and EtherNet/IP connections cannot be used at the same time.

• Can be connected simultaneously via Ethernet with PC tools (Sysmac Studio, SmartMonitorZW) and another 

device (PLC etc). Can be connected simultaneously via Ethernet with PC tools (Sysmac Studio, SmartMonitorZW) 

and another device (PLC etc). The port number for the PC tool is 9600 (fixed) and 9602 (fixed). When connecting 

different devices, set the port number to other than 9600 and 9602 (default value is 9601).

Connected to 
ZW-8000

@

 

ZW-7000

@

ZW-5000

@

Other connection

EtherCAT

EtherNet/IP

Ethernet 

 

(no-protocol)

RS-232C 

 

(no-protocol)

Parallel I/O Cable

EtherCAT

---

Not compatible

Compatible

Compatible

Compatible

EtherNet/IP

Not compatible

---

Compatible

Compatible

Compatible

Ethernet 

 

(no-protocol)

Compatible

Compatible

---

Compatible

Compatible

RS-232C
(no-protocol)

Compatible

Compatible

Compatible

---

Compatible

Product

Model

Application

ZW

ZW-8000

@

/7000

@

/

5000

@

This Displacement Sensor performs measurements.

PC Tool

Sysmac Studio Standard 
Edition

• SYSMAC-SE200D 

(unlicensed, media 
only, 32-bit version 
DVD)

• SYSMAC-SE200D-64 

(unlicensed, media 
only, 64-bit version 
DVD)

• SYSMAC-SE201L 

 

(1-license edition)

• SYSMAC-SE2

@@

L 

 

(multilicense editions 
(3, 10, 30, or 50 
licenses))

Sysmac Studio 
Measurement Sensor 
Edition

• SYSMAC-NE00

@

L

 

(1 or 3 licences)

This is the setup application. It is part of the Sysmac Studio Package and it 
runs on Windows.
The Sysmac Studio comes in two different editions.

• Sysmac Studio Standard Edition

 

The Sysmac Studio provides an integrated development environment for 
the NX/NJ series Controllers and other Machine Automation Controllers 
and EtherCAT Slaves. It supports setup, programming, debugging, 
operation, and maintenance.

 

The Sysmac Studio Standard Edition DVD includes Support Software for 
EtherNet/IP, DeviceNet, serial communications, and PT screen design 
(CX-Designer). Refer to the Sysmac catalog (Cat. No. P072) for details.

• Sysmac Studio Measurement Sensor Edition

 

This license provides the functions that are required to set up ZW-8000/
7000/5000 Series Vision Sensors from the Sysmac Studio. This model 
number is for the license only. You must also purchase the DVD for the 
Sysmac Studio Standard Edition Ver.1.15 or higher.

Special EtherCAT Cable

Refer to 10-1 
Specifications and 
Dimensions

The Special EtherCAT Cable connects the Sensor to another Sensor or to 
another EtherCAT device.

General-purpose Ethernet 
cable

---

Prepare commercially available Ethernet cable
satisfying the following requirements:

• Category 5e or more, 30 m or less
• RJ45 connector (8-pin modular jack)
• For direct connection: Select cross cable.
• For connection through an industrial switching hub: Select straight cable.

Special I/O Cable

For connecting to a PLC 
or programmable terminal

• ZW-XPT2

For connecting to a PC

• ZW-XRS2

Connect the sensor with a PLC, programmable terminal, or personal 
computer etc..

Important

Содержание ZW-7000 Series

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды