Omron ZW-7000 Series Скачать руководство пользователя страница 246

Страница: 246 / 336

Setting the Output Conditions

244

ZW-8000/7000/5000

User's Manual

Setting the Frequency Filter

Setting the Frequency Filter p.155

As an example, here is an explanation of the procedure for selecting the “LOPASS” setting for the frequency

filter type, and the “1Hz” cut-off frequency filter setting.

Operating procedure

Steps

Key operation

Display

Description

1 to 4

For moving to “FILTER”, see steps 1 to 4 in p.242.

Select “FRQNCY” as the filter type.
Press the

keys to select “FREQ” and press the

key.

Select the frequency filter type.

LO.PASS: LOWPASS FILTER
HIPASS: HIGHPASS FILTER
BD.PASS: BANDPASS FILTER

Select “LOPASS” as the frequency filter type.
The current setting value is displayed on the sub-display.

Press

key to enter editing mode and the sub-display blinks.

In this example, select “LO.PASS” and press the

key.

Set the cut-off frequency.
“CUTOFF” is displayed on the main display and the current setting
value is displayed on the sub-display.

Press

key to enter the editing mode, and the sub-display

blinks.

To edit numerical values, use the

keys.

In this example, input “1”, then press the

key.

The decimal point is displayed.
Press the

key to move the decimal point.

Determine the decimal point and then press the

key.

Press and hold the

key for two seconds or more to enter the

RUN mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222).

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Omron ZW-7000 Series, Руководство пользователя

Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды