Omron ZW-7000 Series Скачать руководство пользователя страница 265

Страница: 265 / 336

Setting the Banks

ZW-8000/7000/5000
User's Manual

263

Senso

r con

trol
ler
ope

ons

Saving the Bank/System Settings

Save the bank/system settings to the Sensor Controller.

• The settings of all banks are saved regardless of the currently selected bank number.

• After you have made or changed settings, be sure to save the setup data. All settings will be deleted if you turn the

power OFF without saving the data.

Here is an explanation of the procedure for saving the bank/system settings.

Operating procedure

Steps

Key operation

Display

Description

Press and hold the

key for two seconds or more to enter the

FUNC mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222).

Press the

keys to select “SYSTEM” and press the

key.

Press the

keys to select “SAVE” and press the

key.

“OK/CAN” is displayed on the sub-display.

Press the

key to save the settings or the

key to

cancel.

Press and hold the

key for two seconds or more to enter the

RUN mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222).

Important

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Omron ZW-7000 Series, Руководство пользователя

Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды