Omron ZW-7000 Series Скачать руководство пользователя страница 318

Страница: 318 / 336

Specifications and External Dimensions

316

ZW-8000/7000/5000

User's Manual

• Secure a minimum bending radius (R) for the fiber cable that is at least as large as the specification value.

A bending radius smaller than the specification value could cause damage to the fiber cable.

• When an extension fiber cable of 2 m or longer is connected, the setting rage of the measurement cycle (exposure

time) changes. For details, refer to "Setting the Measurement Cycle" p.122 in this manual.

●

ZW-XF7002R/XF7005R/XF7010R/XF7020R/XF7030R

• Secure a minimum bending radius (R) for the fiber cable that is at least as large as the specification value.

A bending radius smaller than the specification value could cause damage to the fiber cable.

• When an extension fiber cable of 10 m or longer is connected, the setting rage of the measurement cycle (exposure

time) changes. For details, refer to "Setting the Measurement Cycle" p.122 in this manual.

Item

Specifications

ZW-XF7002R

ZW-XF7005R

ZW-XF7010R

ZW-XF7020R

ZW-XF7030R

Applicable Sensor

Controller

ZW-7000

Applicable Sensor Head

ZW-S70

/SP70

/SPR70

Ambient temperature

Operation: 0 to 50

C, Storage: -15 to +60

C (with no icing or condensation)

Ambient humidity

Operation, storage: 35 to 85%RH (with no icing or condensation)

Vibration resistance
(destructive)

10 to 55 Hz (half amplitude 0.35 mm), 50 mins in each of X/Y/Z directions

Shock resistance
(destructive)

150 m/s

, 6 direction, 3 times each (up/down, left/right, forward/backward)

Fiber length

2 m

5 m

10 m

20 m

30 m

Material

Cable sheath: PVC, Connector: PBT, Connection adapter: PEI

Fiber cable minimum
bending radius

20 mm

Weight

Approx. 25 g

Approx. 45 g

Approx. 70 g

Approx. 120 g

Approx. 160 g

Accessories

Connection adapter (ZW-XFCM), 2 Fiber cable protective cap, 2 straps. Instruction Sheet, Precautions

Note 1. THE FOLLOWING TABLE LI

CABLE LENGTH

PER MODEL

TYPE

PECIFICATION

(

)

2m
5m

ZW-XF7002R
ZW-XF7005R

（

Unit

：

）

(7.7)

2000

＋

40/0

5000

＋

100/0

10m

ZW-XF7010R

10000+200/0

20m

ZW-XF7020R

20000+400/0

ZW-XF70

0000+600/0

(7.7)

FIBER CONNECTOR
(

OR HEAD

IDE)

(25)

(40)

(12.6)

2-0.7 Di

12-0.125 Di

4.6

FIBER CABLE (

.0 Di

L (Note 1)

LABEL

ERIAL No.

NAME PLATE

(25)

(40)

(

(60)

(25.4)

(12.6)

FIBER CONNECTOR
(CONTROLLER

IDE)

2-0.7 Di

12-0.125 Di

4.6

(ACCE

ORIE

)

CONNECTION ADAPTER:ZW-XFCM

14.9

CALE (2 : 1)

Important

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Omron ZW-7000 Series, Руководство пользователя

Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды