Omron ZW-7000 Series Скачать руководство пользователя страница 271

Страница: 271 / 336

Setting the System

ZW-8000/7000/5000
User's Manual

269

Senso

r con

trol
ler
ope

ons

Setting the Key Lock

Setting the Key Lock p.183

Note that, moving to the key lock setting menu or moving between menu hierarchies are possible even when the key
lock function is ON.

Here is an explanation of the procedure for turning the key lock ON.

Operating procedure

Steps

Key operation

Display

Description

Press and hold the

key for two seconds or more to enter the

FUNC mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222)

Press the

keys to select “SYSTEM” and press the

key.

Press the

keys to select “LOCK” and press the

key.

Select key lock ON/OFF.
The current setting value is displayed on the sub-display.

Press the

keys to enter the editing mode, and the sub-

display blinks.
In this example, select “ON” and press the

key.

Press and hold the

key for two seconds or more to enter the

RUN mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222).

Important

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Omron ZW-7000 Series, Руководство пользователя

Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды