manualshive.com logo in svg

Omron ZW-7000 Series, Руководство пользователя

Поделиться
Скачать
Omron ZW-7000 Series Скачать руководство пользователя страница 149

Setting the Output Conditions

ZW-8000/7000/5000 
User's Manual

147

 4 

Settin

gs for Function

3

Select [Actual scaling (two points)], and 

click [Next >].

The [Scaling] popup menu display changes to 

[1st point settings].

4

Set correction of the 1st point.

 

Click [STOP] to fix the [Current value], set 

[Set value] and click [Next >].

The [Scaling] popup menu display changes to 

[2nd point settings].

5

In the same way, set correction of the 2nd 

point.

When the change direction is set and [Next>] is 

clicked, the [Scaling] popup menu display 

changes to [Confirm the scaling parameters], 

and the span and offset values are displayed.

6

Click [OK].

2-point scaling can also be executed by the operating keys on the Sensor Controller.

Performing 2-point Scaling p.248

The current measured value is displayed at 
[Current value], and is refreshed at 100 ms 
cycles. When [STOP] is clicked, refreshing of the 
[Current value] display stops. Clicking the 
[STOP] button again resumes display refreshing.

Note

Note

Содержание ZW-7000 Series

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды