manualshive.com logo in svg

Omron ZW-7000 Series, Руководство пользователя

Поделиться
Скачать
Omron ZW-7000 Series Скачать руководство пользователя страница 250

Setting the Output Conditions

248

ZW-8000/7000/5000 

User's Manual

Performing 2-point Scaling

Performing 2-point Scaling p.146

Operating procedure

Steps

Key operation

Display

Description

1 to 5

For moving to “SCALE”, see steps 1 to 5 in p.246. 

6

Select “AUTO” as the scaling type. 
The current setting value is displayed on the sub-display.

Press 

/

 key to enter editing mode and the sub-display blinks.

Select “AUTO” and press the 

 key. 

7

Press the 

/

 keys to select “2PT” and press the 

 key. 

8

Press the 

 key when the main display shows “POINT1”. 

9

Set the measured value of point 1. 
The current measured value is displayed on the main display and the 
current setting value is displayed on the sub-display. 

To edit numerical values, use the 

/

/

/

 keys.

Enter the setting value and then press the 

 key.

10

Press the 

 key when the main display shows “POINT2”. 

11

Set the measured value of point 2. 

To edit numerical values, use the 

/

/

/

 keys.

Enter the setting value and then press the 

 key.

12

“OK/CAN” is displayed on the sub-display. 

Press the 

 key to execute scaling or 

 key to cancel. 

13

Press and hold the 

 key for two seconds or more to enter the 

RUN mode.
To save the setting, refer to "7-3 Functions of Operating Keys" 
(p.222).

Содержание ZW-7000 Series

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды