Omron ZW-7000 Series Скачать руководство пользователя страница 248

Страница: 248 / 336

Setting the Output Conditions

246

ZW-8000/7000/5000

User's Manual

Setting Scaling

Performing Manual Scaling

Performing Manual Scaling p.143

As an example, here is an explanation of the procedure for setting the manual scaling type to “SPAN” and the

inclination coefficient to “1.2”.

Operating procedure

Steps

Key operation

Display

Description

Press and hold the

key for two seconds or more to enter the

FUNC mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222).

Press the

keys to select “MEAS” and press the

key.

If "TASK 1" is displayed, press the

key. If "TASK 1" is not

displayed, press the

key to select "TASK 1", and then

press the

key.

Press the

keys to select “OUTPUT” and press the

key.

Press the

keys to select “SCALE” and press the

key.

Select “MANUAL” as the scaling type.
The current setting value is displayed on the sub-display.

Press the

keys to enter the editing mode, and the sub-

display blinks.
Select “MANUAL” and press the

key.

Set the manual scaling type.

SPAN: Span
OFFSET: Offset

In this example, press the

keys, select “SPAN” and press

the

key.

Set the inclination coefficient.
The current setting value is displayed on the sub-display.

Press the

key to enter the editing mode, and the sub-display

blinks.

To edit numerical values, use the

keys.

In this example, select “1.2” and press the

key.

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Omron ZW-7000 Series, Руководство пользователя, Страница: 248 / 336

Результаты поиска

Содержание ZW-7000 Series

Отзывы: