Omron ZW-7000 Series Скачать руководство пользователя страница 184 | Manualshive

Страница: 184 / 336

Omron ZW-7000 Series Скачать руководство пользователя страница 184

Setting I/O

182

ZW-8000/7000/5000

User's Manual

Assigning digital output

Set the measurement result for digital output.

This setting is applied to the OUT data of the Internal logging, Fieldbus (EtherCAT/Ethernet), and serial data.

Units for each setting values are as follows:

Measurement value

:nm

Amount of emitted light

:0.01% (0.01 to 100.00%)

Amount of received light

:Luminance level (0 to 4095)

Reflection power

:Lv(1 to 10000)

With ZW-8000

@

, the measurement state can be output.

The measurement state can be set to the non-measurement condition, and the reflection power and edge

number judgment result can be checked.

The measurement state is output as the following bit assignments.

1st bit (lowest bit) :Reflection power judgment value

2nd bit

:Edge number judgment value

The output data is output as a decimal number. If the output data is "2" for example, the 1st bit (lowest bit) is "0"

and the 2nd bit is 1 (2'b10).

The measurement state at this time does not meet the edge number comparison condition and is less than the

reflection power threshold.



Multi View Explore

: [Bank Group] | [(Bank Data Name)] (double click)

→

Edit pane

: [I/O Settings] icon (

)

→

I/O Setting Screen

: [Digital output]

Item

Setting item

Setting value

Description

Digital output

Output target*
(OUT *)

None/TASK1/TASK2/TASK3/TASK4/
Amount of emitted light (Area1)/
Peak amount of received light (Area1)/
Light power (Area 1) / Peak amount of received light (Area 1)/
Incident level (1st edge of Area 1)/
Incident level (2nd edge of Area 1)/
Incident level (3rd edge of Area 1)/
Incident level (4th edge of Area 1)/
Light power (Area 2)/Peak amount of received light (Area 2)/Incident
level (1st edge of Area 2)/Incident level (2nd edge of Area 2)/Incident
level (3rd edge of Area 2)/Incident level (4th edge of Area 2)
Measurement state

(ZW-8000

@

only) /

Reflection power (ZW-8000

@

only)

Set the Measurement
result for digital output.

1

Select the measurement value in [Output

target*(OUT*)].

«
...
182
183
184
185
186
...
»

Содержание ZW-7000 Series

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды