Omron ZW-7000 Series Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 336

Omron ZW-7000 Series Скачать руководство пользователя страница 81

Wiring

ZW-8000/7000/5000
User's Manual

2

In

sta
llatio

n

a

nd

Con

nection

s

79

Class

Name

Description

Parallel

output

HIGH output

This outputs judgment results - HIGH (HIGH threshold values < Measured value).

PASS output

This outputs judgment results - PASS (LOW threshold values

≤

Measured value

≤

HIGH

threshold values).

LOW output

This outputs judgment results - LOW (LOW threshold values > Measured value).

ALARM output

This turns ON when there is a system error.

BUSY output

This turns ON during sampling with the hold function enabled. It allows you to check
whether or not the self-trigger is functioning correctly.

It also turns ON during bank switching.

ENABLE output

This turns ON when the sensor is ready for measurement.
This output is interlocked with the ENABLE indicator.

BANK_OUT output

This outputs the currently specified bank number.
It expresses the bank number in combinations of BANK_OUT1, 2 and 3.

SYNCFLG/TRIGBUSY
output

In the internal/PDO synchronized mode, this output operates as SYNCFLG. This turns ON
when measurement synchronization processing is executed by SYNC input and the state
changes to one where normal measurement values can be output.
In the external synchronous measurement mode, this output operates as TRIGBUSY. This
turns ON while a measurement by TRIG input is being performed. The next TRIG input
cannot be turned ON until this turns OFF.

STABILITY output

This turns ON when 1surface is within the measurement range.
This output is interlocked with the STABILITY indicator.

LOGSTAT output

This turns ON while internal logging is in execution.

LOGERR output

This turns ON when internal logging fails. Turns ON when the maximum number of logging
results are saved and you try to execute internal logging. If the LOGGING signal turns OFF,
LOGERR signal is also turned OFF.

TASKSTAT output

This turns ON when the measurement value is finalized.

In FUNC mode, output of each signals are the followings;

• BUSY output Turns ON

BANK_OUT Outputs the current bank number

Other signals Turns OFF

Bank Number BANK_OUT1

BANK_OUT2

BANK_OUT3

BANK1

OFF

OFF

OFF

BANK2

ON

OFF

OFF

BANK3

OFF

ON

OFF

BANK4

ON

ON

OFF

BANK5

OFF

OFF

ON

BANK6

ON

OFF

ON

BANK7

OFF

ON

ON

BANK8

ON

ON

ON

«
...
79
80
81
82
83
...
»

Содержание ZW-7000 Series

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды