Omron ZW-7000 Series Скачать руководство пользователя страница 327

Страница: 327 / 336

Firmware Update

ZW-8000/7000/5000
User's Manual

325

APPE

NDICE

Performing the Update on Warp Engine ZW-7

The most recent version of the software and PC Tool can be downloaded from the following website for

OMRON members. Refer to the Member Registration Sheet that is enclosed with the Sensor.

http://www.fa.omron.co.jp/zw

Connect the the PC which is installed Warp Engine ZW-7 to ZW via Ethernet before operating.

• Use Warp Engine ZW-7 for updating ZW-8000/5000 series.

• Only start Warp Engine ZW-7 when the computer has recognized the Sensor Controller normally.

• When using Warp Engine ZW-7 on the same PC as Sysmac Studio Measurement Sensor Edition 7, do not change

the current IP address and subnet mask being used. If you are using a different personal computer, refer to “5-1

Connecting by No-protocol Communications” described in Displacement Sensor ZW-7000/5000 series Confocal

Fiber Type Displacement Sensor User’s Manual for Communications Settings (Z363) and change the IP address

and the subnet mask of the Sensor Controller.

• ZW-8000 firmware updates cannot be performed using Warp Engine ZW-7 Ver. 2.0 or earlier.

Check the content of the message, and click

[OK].

The firmware update is started.

A progress bar is displayed during update

processing. Wait for the [Firmware Write

Completed] popup to be displayed. (The update

takes several minutes to complete.)

• Errors may occur on the Sensor Controller

during updating, but just wait for the update to

complete.

• If the update progress bar stops midway or the

update does not end even after ten minutes,

there is the possibility that the update has failed.

In this case, contact an OMRON branch or sales

office about the firmware version before update

and the firmware version in the write file.

Click [Close].

The firmware update is completed.

Important

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Omron ZW-7000 Series, Руководство пользователя

Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды