Niveo NGSME48T4H Скачать руководство пользователя страница 146

Страница: 146 / 338

Chapter

3: Web Management

LLDP - LLDP

PoE Switch User Manual | 146

Tx Reinit

When a port is disabled, LLDP is disabled or the switch is rebooted, an LLDP shutdown frame

is transmitted to the neighboring units, Signaling that the LLDP information isn't valid

anymore. Tx Reinit controls the amount of seconds between the shutdown frame and a new

LLDP initialization. Valid values are restricted to 1 - 10 seconds.

LLDP Port Configuration

The LLDP port settings relate to the currently selected stack unit, as reflected by the page

header.

Port

The switch port number of the logical LLDP port.

Mode

Select LLDP mode.

Rx only The switch will not send out LLDP information, but LLDP information from neighbor

units is analyzed.

Tx only The switch will drop LLDP information received from neighbors, but will send out

LLDP information.

Disabled The switch will not send out LLDP information, and will drop LLDP information

received from neighbors.

Enabled The switch will send out LLDP information, and will analyze LLDP information

received from neighbors.

CDP Aware

Select CDP awareness.

The CDP operation is restricted to decoding incoming CDP frames (The switch doesn't

transmit CDP frames). CDP frames are only decoded if LLDP on the port is enabled.

Only CDP TLVs that can be mapped to a corresponding field in the LLDP neighbors' table are

decoded. All other TLVs are discarded (Unrecognized CDP TLVs and discarded CDP frames

are not shown in the LLDP statistics.). CDP TLVs are mapped onto LLDP neighbors' table as

shown below.

CDP TLV "Device ID" is mapped to the LLDP "Chassis ID" field.

CDP TLV "Address" is mapped to the LLDP "Management Address" field. The CDP address

TLV can contain multiple addresses, but only the first address is shown in the LLDP

neighbors table.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды