Niveo NGSME48T4H Скачать руководство пользователя страница 120

Страница: 120 / 338

Chapter

3: Web Management

Spanning Tree - MSTI Mapping

PoE Switch User Manual | 120

3.1.8.2. Spanning Tree - MSTI Mapping

This page allows the user to inspect the current STP MSTI bridge instance priority

configurations, and possibly change them as well.

Configuration Identification

Configuration Name

The name identifying the VLAN to MSTI mapping. Bridges must share the name and revision

(see below), as well as the VLAN-to-MSTI mapping configuration in order to share spanning

trees for MSTI's (Intra-region). The name is at most 32 characters.

Configuration Revision

The revision of the MSTI configuration named above. This must be an integer between 0 and

65535.

MSTI Mapping

MSTI

The bridge instance. The CIST is not available for explicit mapping, as it will receive the

VLANs not explicitly mapped.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды