Niveo NGSME48T4H Скачать руководство пользователя страница 267

Страница: 267 / 338

Chapter

3: Web Management

Monitor - Loop Protection

PoE Switch User Manual | 267

3.2.7. Monitor - Loop Protection

This page displays the loop protection port status the ports of the currently selected switch.

Port

The switch port number of the logical port.

Action

The currently configured port action.

Transmit

The currently configured port transmit mode.

Loops

The number of loops detected on this port.

Status

The current loop protection status of the port.

Loop

Whether a loop is currently detected on the port.

Time of Last Loop

The time of the last loop event detected.

Buttons



Refresh:

Click to refresh the page immediately.



Auto-refresh:

Check this box to enable an automatic refresh of the page at regular

intervals.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды