Niveo NGSME48T4H Скачать руководство пользователя страница 283

Страница: 283 / 338

Chapter

3: Web Management

IPMC - MLD Snooping - IPv6 Group Information

PoE Switch User Manual | 283

3.2.10.2.3. IPMC - MLD Snooping - IPv6 Group Information

Entries in the MLD SFM Information Table are shown on this page. The MLD SFM

(Source-Filtered Multicast) Information Table also contains the SSM (Source-Specific

Multicast) information. This table is sorted first by VLAN ID, then by group, and then by Port.

Different source addresses belong to the same group are treated as single entry.

Navigating the MLD SFM Information Table

Each page shows up to 99 entries from the MLD SFM Information table, default being 20,

selected through the "entries per page" input field. When first visited, the web page will

show the first 20 entries from the beginning of the MLD SFM Information Table.

The "Start from VLAN", and "group" input fields allow the user to select the starting point in

the MLD SFM Information Table. Clicking the Refresh button will update the displayed table

starting from that or the closest next MLD SFM Information Table match. In addition, the

two input fields will - upon a Refresh button click - assume the value of the first displayed

entry, allowing for continuous refresh with the same start address.

The

“<<” will use the last entry of the currently displayed table as a basis for the next

lookup. When the end is reached the text "No more entries" is shown in the displayed table.

Use the

“|<<” button to start over.

MLD SFM Information Table Columns

VLAN ID

VLAN ID of the group.

Group

Group address of the group displayed.

Port

Switch port number.

Mode

Indicates the filtering mode maintained per (VLAN ID, port number, Group Address) basis.

It can be either Include or Exclude.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды