Niveo NGSME48T4H Скачать руководство пользователя страница 205

Страница: 205 / 338

Chapter

3: Web Management

Configuration - sFlow

PoE Switch User Manual | 205

3.1.23. Configuration - sFlow

This page allows for configuring sFlow. The configuration is divided into two parts:

Configuration of the sFlow receiver (a.k.a. sFlow collector) and configuration of per-port flow

and counter samplers.

sFlow configuration is not persisted to non-volatile memory, which means that a reboot or

master change will disable sFlow sampling.

Receiver Configuration

Owner

Basically, sFlow can be configured in two ways: Through local management using the Web or

CLI interface or through SNMP. This read-only field shows the owner of the current sFlow

configuration and assumes values as follows:



If sFlow is currently unconfigured/unclaimed, Owner contains <none>.



If sFlow is currently configured through Web or CLI, Owner contains <Configured

through local management>.



If sFlow is currently configured through SNMP, Owner contains a string identifying the

sFlow receiver.

If sFlow is configured through SNMP, all controls - except for the Release-button - are

disabled to avoid inadvertent reconfiguration.

The

“

Release

” button allows for releasing the current owner and disable sFlow sampling. The

button is disabled if sFlow is currently unclaimed. If configured through SNMP, the release

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды