Niveo NGSME48T4H Скачать руководство пользователя страница 219

Страница: 219 / 338

Chapter

3: Web Management

Ports - Detailed Statistics

PoE Switch User Manual | 219

3.2.3.4. Ports - Detailed Statistics

This page provides detailed traffic statistics for a specific switch port. Use the port select box

to select which switch port details to display.

The selected port belongs to the currently selected stack unit, as reflected by the page

header.

The displayed counters are the totals for receive and transmit, the size counters for receive

and transmit, and the error counters for receive and transmit.

Receive Total and Transmit Total

Rx and Tx Packets

The number of received and transmitted (good and bad) packets.

Rx and Tx Octets

The number of received and transmitted (good and bad) bytes. Includes FCS, but excludes

framing bits.

Rx and Tx Unicast

The number of received and transmitted (good and bad) unicast packets.

Rx and Tx Multicast

The number of received and transmitted (good and bad) multicast packets.

Rx and Tx Broadcast

The number of received and transmitted (good and bad) broadcast packets.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды