Niveo NGSME48T4H Скачать руководство пользователя страница 264

Страница: 264 / 338

Chapter

3: Web Management

LACP - System Status

PoE Switch User Manual | 264

3.2.6. Monitor - LACP

3.2.6.1. LACP - System Status

This page provides a status overview for all LACP instances.

Aggr ID

The Aggregation ID associated with this aggregation instance. For LLAG the id is shown as

'isid:aggr-id' and for GLAGs as 'aggr-id'

Partner System ID

The system ID (MAC address) of the aggregation partner.

Partner Key

The Key that the partner has assigned to this aggregation ID.

Last changed

The time since this aggregation changed.

Local Ports

Shows which ports are a part of this aggregation for this switch/stack. The format is: "Switch

ID:Port".

Buttons



Auto-refresh:

Check this box to refresh the page automatically. Automatic refresh

occurs every 3 seconds.



Refresh:

Click to refresh the page.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды