Niveo NGSME48T4H Скачать руководство пользователя страница 141

Страница: 141 / 338

Chapter

3: Web Management

IPMC - MLD Snooping - Basic Configuration

PoE Switch User Manual | 141

Router Port

Specify which ports act as router ports. A router port is a port on the Ethernet switch that

leads towards the Layer 3 multicast device or MLD querier.

If an aggregation member port is selected as a router port, the whole aggregation will act

as a router port.

Fast Leave

Enable the fast leave on the port.

Throttling

Enable to limit the number of multicast groups to which a switch port can belong.

Buttons



Save:

Click to save changes.



Reset:

Click to undo any changes made locally and revert to previously saved

values.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды