Niveo NGSME48T4H Скачать руководство пользователя страница 191

Страница: 191 / 338

Chapter

3: Web Management

QoS - Port Tag Remarking

PoE Switch User Manual | 191

DP level Configuration

Controls the Drop Precedence level translation table when the mode is set to Mapped.

The purpose of this table is to reduce the 2 bit classified DP level to a 1 bit DP level used in

the (QoS class, DP level) to (PCP, DEI) mapping process.

(QoS class, DP level) to (PCP, DEI) Mapping

Controls the mapping of the classified (QoS class, DP level) to (PCP, DEI) values when the

mode is set to Mapped.

Buttons



Save:

Click to save changes.



Reset:

Click to undo any changes made locally and revert to previously saved values.



Cancel:

Click to undo any changes made locally and return to the previous page.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды