Niveo NGSME48T4H Скачать руководство пользователя страница 33

Страница: 33 / 338

Chapter

3: Web Management

System - Log

NGSME48T4H Switch User Manual | 33

3.1.1.5. System - Log

Configure System Log on this page.

Server Mode

When enabled, the system log message will be sent out to the system log server you set here.

The system log protocol is based on UDP communication and received on UDP port 514 and

the system log server will not send acknowledgments back sender since UDP is a

connectionless protocol and it does not provide acknowledgments. The system log packet will

always send out even if the system log server does not exist. Possible modes are:



Enabled:

Enable server mode operation.



Disabled:

Disable server mode operation.

Server Address

Indicates the IPv4 host address of system log server. If the switch provide DNS feature, it

also can be a host name.

System log Level

Indicates what kind of message will send to system log server. Possible modes are:



Info:

Send information, warnings and errors.



Warning:

Send warnings and errors.



Error:

Send errors.

Buttons



Save:

Click to save changes.



Reset:

Click to undo any changes made locally and revert to previously saved values.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды