Niveo NGSME48T4H Скачать руководство пользователя страница 40

Страница: 40 / 338

Chapter

3: Web Management

DHCP - Server - Mode

NGSME48T4H Switch User Manual | 40

3.1.4. Configuration - DHCP

3.1.4.1. DHCP - Server

3.1.4.1.1. DHCP - Server - Mode

This page configures global mode and VLAN mode to enable/disable DHCP server per

system and per VLAN.

Global Mode

Configure operation mode to enable/disable DHCP server per system.

Mode

Configure the operation mode per system. Possible modes are:



Enabled:

Enable DHCP server per system.



Disabled:

Disable DHCP server pre system.

VLAN Mode

Configure operation mode to enable/disable DHCP server per VLAN.

VLAN Range

Indicate the VLAN range in which DHCP server is enabled or disabled. The first VLAN ID

must be smaller than or equal to the second VLAN ID. BUT, if the VLAN range contains

only 1 VLAN ID, then you can just input it into either one of the first and second VLAN ID or

both.

On the other hand, if you want to disable existed VLAN range, then you can follow the

steps.

1. Press

“Add VLAN Range” to add a new VLAN range.

2. Input the VLAN range that you want to disable.

3. Choose Mode to be Disabled.

4. Press

“Save” to apply the change.

Then, you will see the disabled VLAN range is removed from the DHCP Server mode

configuration page.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды