Niveo NGSME48T4H Скачать руководство пользователя страница 39

Страница: 39 / 338

Chapter

3: Web Management

Configuration - Ports

PoE Switch User Manual | 39

result of the last Auto-Negotiation.

Check the configured column to use flow control. This setting is related to the setting for

Configured Link Speed.

Maximum Frame Size

Enter the maximum frame size allowed for the switch port, including FCS.

Excessive Collision Mode

Configure port transmit collision behavior.



Discard:

Discard frame after 16 collisions (default).



Restart:

Restart backoff algorithm after 16 collisions.

Buttons



Save:

Click to save changes.



Reset:

Click to undo any changes made locally and revert to previously saved values.



Refresh:

Click to refresh the page. Any changes made locally will be undone.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды